2018-10-31 15:22:17,597 - serial.log is currently not enabled, you can enable it via Settings > Serial Connection > Log communication to serial.log 2018-10-31 15:22:20,078 - Enabling serial logging 2018-10-31 15:22:23,749 - Send: M105 2018-10-31 15:24:28,861 - Recv: ok T:21.9 /0.0 T0:21.9 /0.0 B:20.3 /0.0 2018-10-31 15:24:32,859 - Changing monitoring state from "Operational" to "Printing" 2018-10-31 15:24:32,896 - Send: N0 M110 N0*125 2018-10-31 15:24:32,904 - Recv: ok 2018-10-31 15:24:32,912 - Send: N1 G28*18 2018-10-31 15:24:35,963 - Recv: ok 2018-10-31 15:24:35,968 - Send: N2 G1 Z10 F1000.0*40 2018-10-31 15:24:35,978 - Recv: ok 2018-10-31 15:24:36,973 - Send: N4 M118 P1 S"// action:prompt_begin Part Ok?"*9 2018-10-31 15:24:36,980 - Recv: // action:prompt_begin Part Ok?ok 2018-10-31 15:25:07,000 - Communication timeout while printing, trying to trigger response from printer. Configure long running commands or increase communication timeout if that happens regularly on specific commands or long moves. 2018-10-31 15:25:07,011 - Send: N5 M105*34 2018-10-31 15:25:07,016 - Recv: ok T:21.8 /0.0 T0:21.8 /0.0 B:20.7 /0.0 2018-10-31 15:25:07,021 - Send: N6 M105*33 2018-10-31 15:25:07,026 - Recv: ok T:21.8 /0.0 T0:21.8 /0.0 B:20.7 /0.0 2018-10-31 15:25:07,033 - Send: N7 M118 P1 S"// action:prompt_button No"*86 2018-10-31 15:25:07,037 - Recv: // action:prompt_button Nook 2018-10-31 15:25:37,073 - Communication timeout while printing, trying to trigger response from printer. Configure long running commands or increase communication timeout if that happens regularly on specific commands or long moves. 2018-10-31 15:25:37,084 - Send: N8 M105*47 2018-10-31 15:25:37,090 - Recv: ok T:20.9 /0.0 T0:20.9 /0.0 B:20.4 /0.0 2018-10-31 15:25:37,095 - Send: N9 M105*46 2018-10-31 15:25:37,100 - Recv: ok T:20.9 /0.0 T0:20.9 /0.0 B:20.4 /0.0 2018-10-31 15:25:37,106 - Send: N10 M118 P1 S"// action:prompt_button Yes"*14 2018-10-31 15:25:37,112 - Recv: // action:prompt_button Yesok 2018-10-31 15:26:07,120 - Communication timeout while printing, trying to trigger response from printer. Configure long running commands or increase communication timeout if that happens regularly on specific commands or long moves. 2018-10-31 15:26:07,131 - Send: N11 M105*23 2018-10-31 15:26:07,136 - Recv: ok T:22.4 /0.0 T0:22.4 /0.0 B:20.2 /0.0 2018-10-31 15:26:07,142 - Send: N12 M105*20 2018-10-31 15:26:07,147 - Recv: ok T:22.4 /0.0 T0:22.4 /0.0 B:20.2 /0.0 2018-10-31 15:26:07,153 - Send: N13 M118 P1 S"// action:prompt_show"*119 2018-10-31 15:26:07,158 - Recv: // action:prompt_showok 2018-10-31 15:26:37,191 - Communication timeout while printing, trying to trigger response from printer. Configure long running commands or increase communication timeout if that happens regularly on specific commands or long moves. 2018-10-31 15:26:37,200 - Send: N14 M105*18 2018-10-31 15:26:37,209 - Recv: ok T:23.4 /0.0 T0:23.4 /0.0 B:20.4 /0.0 2018-10-31 15:26:37,215 - Send: N15 M105*19 2018-10-31 15:26:37,219 - Recv: ok T:23.4 /0.0 T0:23.4 /0.0 B:20.4 /0.0 2018-10-31 15:26:37,225 - Send: N16 G1 Z5 F1000.0*41 2018-10-31 15:26:37,232 - Recv: ok 2018-10-31 15:26:37,237 - Send: N17 M84*41 2018-10-31 15:26:38,060 - Recv: ok 2018-10-31 15:26:38,065 - Send: http://10.0.1.131:1880/hevo?format=json,1.1&name=test" 2018-10-31 15:26:38,071 - Changing monitoring state from "Printing" to "Finishing" 2018-10-31 15:26:38,075 - Recv: Bad command: http://10.0.1.131:1880/hevo?format=json,1.1&name=test" 2018-10-31 15:26:38,082 - Recv: ok 2018-10-31 15:26:38,107 - Send: N18 M400*30 2018-10-31 15:26:38,111 - Send: N19 M84*39 2018-10-31 15:26:38,113 - Recv: ok 2018-10-31 15:26:38,120 - Send: N20 M104 T0 S0*19 2018-10-31 15:26:38,121 - Recv: ok 2018-10-31 15:26:38,129 - Send: N21 M140 S0*86 2018-10-31 15:26:38,131 - Recv: ok 2018-10-31 15:26:38,136 - Recv: ok 2018-10-31 15:26:38,137 - Send: N22 M106 S0*87 2018-10-31 15:26:38,142 - Changing monitoring state from "Finishing" to "Operational" 2018-10-31 15:26:38,153 - Recv: ok