2018-08-20 18:45:23,702 - Changing monitoring state from "Offline" to "Detecting serial port"
2018-08-20 18:45:23,736 - Serial port list: ['/dev/ttyUSB0']
2018-08-20 18:45:23,737 - Connecting to: /dev/ttyUSB0
2018-08-20 18:45:23,792 - Changing monitoring state from "Detecting serial port" to "Opening serial port"
2018-08-20 18:45:23,794 - Connected to: Serial<id=0x6f086850, open=True>(port='/dev/ttyUSB0', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2018-08-20 18:45:23,795 - Starting baud rate detection...
2018-08-20 18:45:23,795 - Changing monitoring state from "Opening serial port" to "Detecting baudrate"
2018-08-20 18:45:24,807 - Trying baudrate: 115200
2018-08-20 18:45:24,818 - Send: N0 M110 N0*125
2018-08-20 18:45:26,670 - Recv: echo:SD init fail
2018-08-20 18:45:26,680 - Recv: start
2018-08-20 18:45:26,686 - Changing monitoring state from "Detecting baudrate" to "Operational"
2018-08-20 18:45:26,702 - Recv: echo:Marlin 1.1.4
2018-08-20 18:45:26,704 - Recv: 
2018-08-20 18:45:26,706 - Recv: echo: Last Updated: 2017-07-04 12:00 | Author: (none, default config)
2018-08-20 18:45:26,711 - Send: N0 M110 N0*125
2018-08-20 18:45:26,714 - Recv: Compiled: Jan 30 2018
2018-08-20 18:45:26,718 - Recv: echo: Free Memory: 4089  PlannerBufferBytes: 1232
2018-08-20 18:45:26,722 - Recv: Here=-0.40
2018-08-20 18:45:26,726 - Recv: echo:V07 stored settings retrieved (466 bytes; crc -22201)
2018-08-20 18:45:26,729 - Recv: echo:  G21    ; Units in mm
2018-08-20 18:45:26,730 - Recv: echo:  M149 C ; Units in Celsius
2018-08-20 18:45:26,733 - Recv: 
2018-08-20 18:45:26,738 - Recv: echo:Filament settings: Disabled
2018-08-20 18:45:26,742 - Recv: echo:  M200 D3.00
2018-08-20 18:45:26,745 - Recv: echo:  M200 D0
2018-08-20 18:45:26,747 - Recv: echo:Steps per unit:
2018-08-20 18:45:26,750 - Recv: echo:  M92 X81.00 Y81.00 Z400.50 E94.30
2018-08-20 18:45:26,753 - Recv: echo:Maximum feedrates (units/s):
2018-08-20 18:45:26,755 - Recv: echo:  M203 X300.00 Y300.00 Z5.00 E25.00
2018-08-20 18:45:26,757 - Recv: echo:Maximum Acceleration (units/s2):
2018-08-20 18:45:26,760 - Recv: echo:  M201 X3000 Y3000 Z100 E3000
2018-08-20 18:45:26,763 - Recv: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
2018-08-20 18:45:26,765 - Recv: echo:  M204 P800.00 R800.00 T1000.00
2018-08-20 18:45:26,767 - Recv: echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>
2018-08-20 18:45:26,769 - Recv: echo:  M205 S0.00 T0.00 B20000 X10.00 Y10.00 Z0.40 E1.00
2018-08-20 18:45:26,772 - Recv: echo:Home offset:
2018-08-20 18:45:26,774 - Recv: echo:  M206 X0.00 Y0.00 Z0.00
2018-08-20 18:45:26,777 - Recv: echo:Auto Bed Leveling:
2018-08-20 18:45:26,779 - Recv: echo:  M420 S1
2018-08-20 18:45:26,781 - Recv: echo:Material heatup parameters:
2018-08-20 18:45:26,783 - Recv: echo:  M145 S0 H200 B60 F0
2018-08-20 18:45:26,786 - Recv:   M145 S1 H240 B80 F0
2018-08-20 18:45:26,788 - Recv: echo:PID settings:
2018-08-20 18:45:26,790 - Recv: echo:  M301 P33.41 I1.47 D189.27
2018-08-20 18:45:26,793 - Recv: echo:Z-Probe Offset (mm):
2018-08-20 18:45:26,794 - Recv: echo:  M851 Z-0.40
2018-08-20 18:45:27,181 - Recv: M1102 status:0
2018-08-20 18:45:27,185 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:27,187 - Send: N1 M115*39
2018-08-20 18:45:27,197 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:27,199 - Send: N2 M21*18
2018-08-20 18:45:27,201 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:27,208 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:30,584 - Send: N3 G91*18
2018-08-20 18:45:30,602 - Send: N4 G1 Z10 F200*3
2018-08-20 18:45:30,609 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:30,620 - Send: N5 G90*21
2018-08-20 18:45:30,623 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:30,631 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:31,689 - Send: N6 M105*33
2018-08-20 18:45:31,703 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:32,871 - Send: N7 G91*22
2018-08-20 18:45:32,890 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:32,900 - Send: N8 G1 Y10 F200*12
2018-08-20 18:45:32,905 - Send: N9 G90*25
2018-08-20 18:45:32,910 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:32,915 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:33,708 - Send: N10 G91*32
2018-08-20 18:45:33,717 - Send: N11 G28 X0 Y0*34
2018-08-20 18:45:33,721 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:33,734 - Send: N12 G90*35
2018-08-20 18:45:33,740 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:33,745 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:36,690 - Send: N13 M105*21
2018-08-20 18:45:36,701 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:37,940 - Changing monitoring state from "Operational" to "Offline"
2018-08-20 18:45:41,224 - Connecting to: /dev/ttyUSB0
2018-08-20 18:45:41,250 - Changing monitoring state from "Offline" to "Opening serial port"
2018-08-20 18:45:41,253 - Connected to: Serial<id=0x69ad8710, open=True>(port='/dev/ttyUSB0', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2018-08-20 18:45:41,255 - Starting baud rate detection...
2018-08-20 18:45:41,255 - Changing monitoring state from "Opening serial port" to "Detecting baudrate"
2018-08-20 18:45:42,261 - Trying baudrate: 115200
2018-08-20 18:45:42,271 - Send: N0 M110 N0*125
2018-08-20 18:45:42,281 - Connection closed, closing down monitor
2018-08-20 18:45:42,285 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:52,300 - Baudrate test retry #1
2018-08-20 18:45:52,314 - Send: N0 M110 N0*125
2018-08-20 18:45:52,323 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:53,329 - Baudrate test retry #2
2018-08-20 18:45:53,337 - Send: N0 M110 N0*125
2018-08-20 18:45:53,348 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:54,354 - Baudrate test retry #3
2018-08-20 18:45:54,365 - Send: N0 M110 N0*125
2018-08-20 18:45:54,374 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:55,379 - Baudrate test retry #4
2018-08-20 18:45:55,390 - Send: N0 M110 N0*125
2018-08-20 18:45:55,400 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:45:56,411 - Trying baudrate: 250000
2018-08-20 18:45:56,419 - Send: N0 M110 N0*125
2018-08-20 18:45:57,419 - Baudrate test retry #1
2018-08-20 18:45:57,424 - Send: N0 M110 N0*125
2018-08-20 18:45:58,425 - Baudrate test retry #2
2018-08-20 18:45:58,436 - Send: N0 M110 N0*125
2018-08-20 18:45:59,443 - Baudrate test retry #3
2018-08-20 18:45:59,454 - Send: N0 M110 N0*125
2018-08-20 18:46:00,455 - Baudrate test retry #4
2018-08-20 18:46:00,469 - Send: N0 M110 N0*125
2018-08-20 18:46:01,469 - Trying baudrate: 230400
2018-08-20 18:46:01,482 - Send: N0 M110 N0*125
2018-08-20 18:46:02,475 - Baudrate test retry #1
2018-08-20 18:46:02,488 - Send: N0 M110 N0*125
2018-08-20 18:46:03,485 - Baudrate test retry #2
2018-08-20 18:46:03,499 - Send: N0 M110 N0*125
2018-08-20 18:46:04,501 - Baudrate test retry #3
2018-08-20 18:46:04,514 - Send: N0 M110 N0*125
2018-08-20 18:46:05,508 - Baudrate test retry #4
2018-08-20 18:46:05,519 - Send: N0 M110 N0*125
2018-08-20 18:46:06,521 - Trying baudrate: 57600
2018-08-20 18:46:06,534 - Send: N0 M110 N0*125
2018-08-20 18:46:07,541 - Baudrate test retry #1
2018-08-20 18:46:07,552 - Send: N0 M110 N0*125
2018-08-20 18:46:08,552 - Baudrate test retry #2
2018-08-20 18:46:08,561 - Send: N0 M110 N0*125
2018-08-20 18:46:09,563 - Baudrate test retry #3
2018-08-20 18:46:09,568 - Send: N0 M110 N0*125
2018-08-20 18:46:10,569 - Baudrate test retry #4
2018-08-20 18:46:10,582 - Send: N0 M110 N0*125
2018-08-20 18:46:11,585 - Trying baudrate: 38400
2018-08-20 18:46:11,598 - Send: N0 M110 N0*125
2018-08-20 18:46:12,598 - Baudrate test retry #1
2018-08-20 18:46:12,609 - Send: N0 M110 N0*125
2018-08-20 18:46:13,604 - Baudrate test retry #2
2018-08-20 18:46:13,615 - Send: N0 M110 N0*125
2018-08-20 18:46:14,617 - Baudrate test retry #3
2018-08-20 18:46:14,630 - Send: N0 M110 N0*125
2018-08-20 18:46:15,629 - Baudrate test retry #4
2018-08-20 18:46:15,638 - Send: N0 M110 N0*125
2018-08-20 18:46:16,651 - Trying baudrate: 19200
2018-08-20 18:46:16,659 - Send: N0 M110 N0*125
2018-08-20 18:46:17,666 - Baudrate test retry #1
2018-08-20 18:46:17,678 - Send: N0 M110 N0*125
2018-08-20 18:46:18,676 - Baudrate test retry #2
2018-08-20 18:46:18,689 - Send: N0 M110 N0*125
2018-08-20 18:46:19,685 - Baudrate test retry #3
2018-08-20 18:46:19,697 - Send: N0 M110 N0*125
2018-08-20 18:46:20,701 - Baudrate test retry #4
2018-08-20 18:46:20,715 - Send: N0 M110 N0*125
2018-08-20 18:46:21,714 - Trying baudrate: 9600
2018-08-20 18:46:21,720 - Send: N0 M110 N0*125
2018-08-20 18:46:22,720 - Baudrate test retry #1
2018-08-20 18:46:22,726 - Send: N0 M110 N0*125
2018-08-20 18:46:23,727 - Baudrate test retry #2
2018-08-20 18:46:23,743 - Send: N0 M110 N0*125
2018-08-20 18:46:24,743 - Baudrate test retry #3
2018-08-20 18:46:24,753 - Send: N0 M110 N0*125
2018-08-20 18:46:25,750 - Baudrate test retry #4
2018-08-20 18:46:25,761 - Send: N0 M110 N0*125
2018-08-20 18:46:26,762 - Changing monitoring state from "Detecting baudrate" to "Error: No more baudrates to test, and no suitable baudrate found."
2018-08-20 18:46:26,780 - Changing monitoring state from "Error: No more baudrates to test, and no suitable baudrate found." to "Offline (Error: No more baudrates to test, and no suitable baudrate found.)"
2018-08-20 18:46:26,789 - Connection closed, closing down monitor
2018-08-20 18:46:33,776 - Changing monitoring state from "Offline" to "Detecting serial port"
2018-08-20 18:46:33,811 - Serial port list: ['/dev/ttyUSB0']
2018-08-20 18:46:33,812 - Connecting to: /dev/ttyUSB0
2018-08-20 18:46:33,918 - Changing monitoring state from "Detecting serial port" to "Opening serial port"
2018-08-20 18:46:33,925 - Connected to: Serial<id=0x69990130, open=True>(port='/dev/ttyUSB0', baudrate=115200, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2018-08-20 18:46:33,927 - Changing monitoring state from "Opening serial port" to "Connecting"
2018-08-20 18:46:33,937 - Send: N0 M110 N0*125
2018-08-20 18:46:36,805 - Recv: echo:SD init fail
2018-08-20 18:46:36,816 - Recv: start
2018-08-20 18:46:36,826 - Send: N0 M110 N0*125
2018-08-20 18:46:36,829 - Recv: echo:Marlin 1.1.4
2018-08-20 18:46:36,833 - Recv: 
2018-08-20 18:46:36,836 - Recv: echo: Last Updated: 2017-07-04 12:00 | Author: (none, default config)
2018-08-20 18:46:36,838 - Recv: Compiled: Jan 30 2018
2018-08-20 18:46:36,840 - Recv: echo: Free Memory: 4089  PlannerBufferBytes: 1232
2018-08-20 18:46:36,843 - Recv: Here=-0.40
2018-08-20 18:46:36,845 - Recv: echo:V07 stored settings retrieved (466 bytes; crc -22201)
2018-08-20 18:46:36,848 - Recv: echo:  G21    ; Units in mm
2018-08-20 18:46:36,850 - Recv: echo:  M149 C ; Units in Celsius
2018-08-20 18:46:36,853 - Recv: 
2018-08-20 18:46:36,855 - Recv: echo:Filament settings: Disabled
2018-08-20 18:46:36,857 - Recv: echo:  M200 D3.00
2018-08-20 18:46:36,860 - Recv: echo:  M200 D0
2018-08-20 18:46:36,862 - Recv: echo:Steps per unit:
2018-08-20 18:46:36,865 - Recv: echo:  M92 X81.00 Y81.00 Z400.50 E94.30
2018-08-20 18:46:36,868 - Recv: echo:Maximum feedrates (units/s):
2018-08-20 18:46:36,871 - Recv: echo:  M203 X300.00 Y300.00 Z5.00 E25.00
2018-08-20 18:46:36,873 - Recv: echo:Maximum Acceleration (units/s2):
2018-08-20 18:46:36,876 - Recv: echo:  M201 X3000 Y3000 Z100 E3000
2018-08-20 18:46:36,878 - Recv: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
2018-08-20 18:46:36,880 - Recv: echo:  M204 P800.00 R800.00 T1000.00
2018-08-20 18:46:36,883 - Recv: echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>
2018-08-20 18:46:36,886 - Recv: echo:  M205 S0.00 T0.00 B20000 X10.00 Y10.00 Z0.40 E1.00
2018-08-20 18:46:36,889 - Recv: echo:Home offset:
2018-08-20 18:46:36,891 - Recv: echo:  M206 X0.00 Y0.00 Z0.00
2018-08-20 18:46:36,893 - Recv: echo:Auto Bed Leveling:
2018-08-20 18:46:36,895 - Recv: echo:  M420 S1
2018-08-20 18:46:36,898 - Recv: echo:Material heatup parameters:
2018-08-20 18:46:36,900 - Recv: echo:  M145 S0 H200 B60 F0
2018-08-20 18:46:36,904 - Recv:   M145 S1 H240 B80 F0
2018-08-20 18:46:36,906 - Recv: echo:PID settings:
2018-08-20 18:46:36,909 - Recv: echo:  M301 P33.41 I1.47 D189.27
2018-08-20 18:46:36,911 - Recv: echo:Z-Probe Offset (mm):
2018-08-20 18:46:36,913 - Recv: echo:  M851 Z-0.40
2018-08-20 18:46:37,324 - Recv: M1102 status:0
2018-08-20 18:46:37,328 - Recv: Error:No Line Number with checksum, Last Line: 0
2018-08-20 18:47:07,360 - There was a timeout while trying to connect to the printer
2018-08-20 18:47:07,373 - Changing monitoring state from "Connecting" to "Offline"
2018-08-20 18:47:07,437 - Connection closed, closing down monitor
2018-08-20 18:47:11,935 - Changing monitoring state from "Offline" to "Detecting serial port"
2018-08-20 18:47:11,971 - Serial port list: ['/dev/ttyUSB0']
2018-08-20 18:47:11,972 - Connecting to: /dev/ttyUSB0
2018-08-20 18:47:12,039 - Changing monitoring state from "Detecting serial port" to "Opening serial port"
2018-08-20 18:47:12,048 - Connected to: Serial<id=0x699905b0, open=True>(port='/dev/ttyUSB0', baudrate=230400, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2018-08-20 18:47:12,051 - Changing monitoring state from "Opening serial port" to "Connecting"
2018-08-20 18:47:12,104 - Send: N0 M110 N0*125
2018-08-20 18:47:43,790 - There was a timeout while trying to connect to the printer
2018-08-20 18:47:43,801 - Changing monitoring state from "Connecting" to "Offline"
2018-08-20 18:47:43,818 - Connection closed, closing down monitor
2018-08-20 18:47:47,382 - Changing monitoring state from "Offline" to "Detecting serial port"
2018-08-20 18:47:47,418 - Serial port list: ['/dev/ttyUSB0']
2018-08-20 18:47:47,419 - Connecting to: /dev/ttyUSB0
2018-08-20 18:47:47,528 - Changing monitoring state from "Detecting serial port" to "Opening serial port"
2018-08-20 18:47:47,535 - Connected to: Serial<id=0x698cbe50, open=True>(port='/dev/ttyUSB0', baudrate=250000, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2018-08-20 18:47:47,537 - Changing monitoring state from "Opening serial port" to "Connecting"
2018-08-20 18:47:47,544 - Send: N0 M110 N0*125
2018-08-20 18:48:20,958 - There was a timeout while trying to connect to the printer
2018-08-20 18:48:20,970 - Changing monitoring state from "Connecting" to "Offline"
2018-08-20 18:48:20,980 - Connection closed, closing down monitor