2022-01-13 08:19:57,807 - serial.log is currently not enabled, you can enable it via Settings > Serial Connection > Log communication to serial.log
2022-01-13 08:23:41,049 - Enabling serial logging
2022-01-13 08:23:44,803 - Changing monitoring state from "Offline" to "Opening serial connection"
2022-01-13 08:23:44,807 - Connecting to port /dev/ttyUSB0, baudrate 19200
2022-01-13 08:23:44,849 - Changing monitoring state from "Opening serial connection" to "Connecting"
2022-01-13 08:23:44,851 - Connected to: Serial<id=0x6ca68a50, open=True>(port='/dev/ttyUSB0', baudrate=19200, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2022-01-13 08:23:44,865 - Send: N0 M110 N0*125
2022-01-13 08:23:53,800 - Connection closed, closing down monitor
2022-01-13 08:23:53,805 - Changing monitoring state from "Connecting" to "Offline"
2022-01-13 08:23:58,684 - Changing monitoring state from "Offline" to "Opening serial connection"
2022-01-13 08:23:58,693 - Connecting to port /dev/ttyUSB0, baudrate 250000
2022-01-13 08:23:58,738 - Changing monitoring state from "Opening serial connection" to "Connecting"
2022-01-13 08:23:58,739 - Connected to: Serial<id=0x6cacd470, open=True>(port='/dev/ttyUSB0', baudrate=250000, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2022-01-13 08:23:58,744 - Send: N0 M110 N0*125
2022-01-13 08:23:59,649 - Recv: start
2022-01-13 08:23:59,654 - Send: N0 M110 N0*125
2022-01-13 08:23:59,666 - Recv: echo:Marlin 1.1.9
2022-01-13 08:23:59,668 - Recv: Marlin-AI3M v1.4.6
2022-01-13 08:23:59,670 - Recv: 
2022-01-13 08:23:59,672 - Recv: echo: Last Updated: 2019-04-03 | Author: (davidramiro)
2022-01-13 08:23:59,676 - Recv: echo:Compiled: Feb 14 2020
2022-01-13 08:23:59,679 - Recv: echo: Free Memory: 1370  PlannerBufferBytes: 1664
2022-01-13 08:23:59,684 - Recv: echo:V55 stored settings retrieved (731 bytes; crc 35317)
2022-01-13 08:23:59,696 - Recv: echo:  G21    ; (mm)
2022-01-13 08:23:59,698 - Recv: 
2022-01-13 08:23:59,700 - Recv: echo:Filament settings: Disabled
2022-01-13 08:23:59,702 - Recv: echo:  M200 D1.75
2022-01-13 08:23:59,708 - Recv: echo:  M200 D0
2022-01-13 08:23:59,714 - Recv: echo:Steps per unit:
2022-01-13 08:23:59,718 - Recv: echo:  M92 X80.73 Y80.72 Z400.99 E395.87
2022-01-13 08:23:59,721 - Recv: echo:Maximum feedrates (units/s):
2022-01-13 08:23:59,724 - Recv: echo:  M203 X500.00 Y500.00 Z6.00 E30.00
2022-01-13 08:23:59,726 - Recv: echo:Maximum Acceleration (units/s2):
2022-01-13 08:23:59,728 - Recv: echo:  M201 X3000 Y2000 Z60 E10000
2022-01-13 08:23:59,730 - Recv: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
2022-01-13 08:23:59,732 - Recv: echo:  M204 P1500.00 R1500.00 T3000.00
2022-01-13 08:23:59,737 - Recv: echo:Advanced: Q<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> X<max_x_jerk> Y<max_y_jerk> Z<max_z_jerk> E<max_e_jerk>
2022-01-13 08:23:59,740 - Recv: echo:  M205 Q20000 S0.00 T0.00 X10.00 Y10.00 Z0.40 E5.00
2022-01-13 08:23:59,743 - Recv: echo:Home offset:
2022-01-13 08:23:59,747 - Recv: echo:  M206 X0.00 Y0.00 Z0.00
2022-01-13 08:23:59,751 - Recv: echo:Mesh Bed Leveling:
2022-01-13 08:23:59,756 - Recv: echo:  M420 S0 Z0.00
2022-01-13 08:23:59,759 - Recv: echo:Endstop adjustment:
2022-01-13 08:23:59,764 - Recv: echo:  M666 Z0.00
2022-01-13 08:23:59,768 - Recv: echo:PID settings:
2022-01-13 08:23:59,772 - Recv: echo:  M301 P15.94 I1.17 D54.19
2022-01-13 08:23:59,776 - Recv: echo:  M304 P251.78 I49.57 D319.73
2022-01-13 08:23:59,780 - Recv: echo:Linear Advance:
2022-01-13 08:23:59,784 - Recv: echo:  M900 K0.00
2022-01-13 08:23:59,788 - Recv: echo:Filament load/unload lengths:
2022-01-13 08:23:59,797 - Recv: echo:  M603 L538.00 U555.00
2022-01-13 08:23:59,984 - Recv: echo:SD card ok
2022-01-13 08:24:00,002 - Recv: ok
2022-01-13 08:24:00,007 - Send: N0 M110 N0*125
2022-01-13 08:24:00,012 - Changing monitoring state from "Connecting" to "Operational"
2022-01-13 08:24:00,072 - Recv: echo:SD card ok
2022-01-13 08:24:00,079 - Recv: ok
2022-01-13 08:24:00,088 - Send: N0 M110 N0*125
2022-01-13 08:24:00,094 - Recv: ok
2022-01-13 08:24:00,101 - Send: N1 M115*39
2022-01-13 08:24:00,122 - Recv: FIRMWARE_NAME:Marlin 1.1.9 (Github, davidramiro) MARLIN-AI3M_VERSION:v1.4.6 SOURCE_CODE_URL:https://github.com/davidramiro/Marlin-AI3M PROTOCOL_VERSION:1.0 MACHINE_TYPE:Anycubic i3 Mega EXTRUDER_COUNT:1 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
2022-01-13 08:24:00,133 - Recv: Cap:SERIAL_XON_XOFF:0
2022-01-13 08:24:00,149 - Recv: Cap:EEPROM:1
2022-01-13 08:24:00,160 - Recv: Cap:VOLUMETRIC:1
2022-01-13 08:24:00,181 - Recv: Cap:AUTOREPORT_TEMP:1
2022-01-13 08:24:00,189 - Recv: Cap:PROGRESS:0
2022-01-13 08:24:00,194 - Recv: Cap:PRINT_JOB:1
2022-01-13 08:24:00,199 - Recv: Cap:AUTOLEVEL:0
2022-01-13 08:24:00,206 - Recv: Cap:Z_PROBE:0
2022-01-13 08:24:00,216 - Recv: Cap:LEVELING_DATA:1
2022-01-13 08:24:00,221 - Recv: Cap:BUILD_PERCENT:0
2022-01-13 08:24:00,229 - Recv: Cap:SOFTWARE_POWER:0
2022-01-13 08:24:00,266 - Recv: Cap:TOGGLE_LIGHTS:0
2022-01-13 08:24:00,310 - Recv: Cap:CASE_LIGHT_BRIGHTNESS:0
2022-01-13 08:24:00,313 - Recv: Cap:EMERGENCY_PARSER:1
2022-01-13 08:24:00,328 - Recv: Cap:AUTOREPORT_SD_STATUS:0
2022-01-13 08:24:00,335 - Recv: Cap:THERMAL_PROTECTION:1
2022-01-13 08:24:00,342 - Recv: ok
2022-01-13 08:24:00,345 - Send: M20
2022-01-13 08:24:00,348 - Recv: Begin file list
2022-01-13 08:24:00,357 - Recv: OWL_PA~1.GCO 6870525
2022-01-13 08:24:00,496 - Recv: AI3MSP~1.GCO 4921117
2022-01-13 08:24:00,500 - Recv: 3DBENC~1.GCO 4978515
2022-01-13 08:24:00,503 - Recv: 3DBENC~2.GCO 3861334
2022-01-13 08:24:00,505 - Recv: AI3MSP~2.GCO 1680464
2022-01-13 08:24:00,508 - Recv: AI3MSP~3.GCO 311883
2022-01-13 08:24:00,511 - Recv: 3_CALI~1.GCO 319166
2022-01-13 08:24:00,514 - Recv: TEFAL_~1.GCO 2578305
2022-01-13 08:24:00,517 - Recv: AI3MSP~4.GCO 2578305
2022-01-13 08:24:00,518 - Recv: WALLTE~1.GCO 41699
2022-01-13 08:24:00,521 - Recv: AIA7D2~1.GCO 189377
2022-01-13 08:24:00,523 - Recv: End file list
2022-01-13 08:24:00,526 - Recv: ok
2022-01-13 08:24:00,534 - Send: M155 S2
2022-01-13 08:24:00,539 - Recv: ok
2022-01-13 08:24:02,558 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:03,639 - Changing monitoring state from "Operational" to "Starting"
2022-01-13 08:24:03,688 - Send: N0 M110 N0*125
2022-01-13 08:24:03,698 - Recv: ok
2022-01-13 08:24:03,709 - Send: N1 G21*27
2022-01-13 08:24:03,714 - Recv: echo:Unknown command: "G21"
2022-01-13 08:24:03,719 - Recv: ok
2022-01-13 08:24:03,726 - Send: N2 G90*18
2022-01-13 08:24:03,731 - Recv: ok
2022-01-13 08:24:03,738 - Send: N3 M82*26
2022-01-13 08:24:03,741 - Recv: ok
2022-01-13 08:24:03,750 - Send: N4 M107*33
2022-01-13 08:24:03,762 - Recv: ok
2022-01-13 08:24:03,771 - Send: N5 M140 S{material_bed_temperature}*82
2022-01-13 08:24:03,776 - Recv: ok
2022-01-13 08:24:03,780 - Send: N6 G4 S60*94
2022-01-13 08:24:04,549 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:05,787 - Recv: echo:busy: processing
2022-01-13 08:24:05,788 - Printer seems to support the busy protocol, will adjust timeouts and set busy interval accordingly
2022-01-13 08:24:06,553 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:07,791 - Recv: echo:busy: processing
2022-01-13 08:24:08,557 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:09,794 - Recv: echo:busy: processing
2022-01-13 08:24:10,560 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:11,796 - Recv: echo:busy: processing
2022-01-13 08:24:12,563 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:13,801 - Recv: echo:busy: processing
2022-01-13 08:24:14,567 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:15,805 - Recv: echo:busy: processing
2022-01-13 08:24:16,572 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:17,809 - Recv: echo:busy: processing
2022-01-13 08:24:18,575 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:19,811 - Recv: echo:busy: processing
2022-01-13 08:24:20,578 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:21,816 - Recv: echo:busy: processing
2022-01-13 08:24:22,582 - Recv:  T:20.00 /0.00 B:21.84 /0.00 @:0 B@:0
2022-01-13 08:24:23,819 - Recv: echo:busy: processing
2022-01-13 08:24:24,585 - Recv:  T:20.00 /0.00 B:21.87 /0.00 @:0 B@:0
2022-01-13 08:24:25,821 - Recv: echo:busy: processing
2022-01-13 08:24:26,588 - Recv:  T:20.00 /0.00 B:21.80 /0.00 @:0 B@:0
2022-01-13 08:24:27,826 - Recv: echo:busy: processing
2022-01-13 08:24:28,591 - Recv:  T:20.00 /0.00 B:21.80 /0.00 @:0 B@:0
2022-01-13 08:24:29,829 - Recv: echo:busy: processing
2022-01-13 08:24:30,597 - Recv:  T:20.00 /0.00 B:21.84 /0.00 @:0 B@:0
2022-01-13 08:24:31,833 - Recv: echo:busy: processing
2022-01-13 08:24:32,600 - Recv:  T:20.00 /0.00 B:21.84 /0.00 @:0 B@:0
2022-01-13 08:24:33,836 - Recv: echo:busy: processing
2022-01-13 08:24:34,603 - Recv:  T:20.00 /0.00 B:21.76 /0.00 @:0 B@:0
2022-01-13 08:24:35,840 - Recv: echo:busy: processing
2022-01-13 08:24:36,607 - Recv:  T:20.00 /0.00 B:21.80 /0.00 @:0 B@:0
2022-01-13 08:24:37,844 - Recv: echo:busy: processing
2022-01-13 08:24:38,610 - Recv:  T:20.00 /0.00 B:21.80 /0.00 @:0 B@:0
2022-01-13 08:24:39,847 - Recv: echo:busy: processing
2022-01-13 08:24:40,613 - Recv:  T:20.00 /0.00 B:21.68 /0.00 @:0 B@:0
2022-01-13 08:24:41,851 - Recv: echo:busy: processing
2022-01-13 08:24:42,617 - Recv:  T:20.00 /0.00 B:21.72 /0.00 @:0 B@:0
2022-01-13 08:24:43,854 - Recv: echo:busy: processing
2022-01-13 08:24:44,620 - Recv:  T:20.00 /0.00 B:21.68 /0.00 @:0 B@:0
2022-01-13 08:24:45,857 - Recv: echo:busy: processing
2022-01-13 08:24:46,624 - Recv:  T:20.00 /0.00 B:21.76 /0.00 @:0 B@:0
2022-01-13 08:24:47,861 - Recv: echo:busy: processing
2022-01-13 08:24:48,627 - Recv:  T:20.00 /0.00 B:21.68 /0.00 @:0 B@:0
2022-01-13 08:24:49,865 - Recv: echo:busy: processing
2022-01-13 08:24:50,632 - Recv:  T:20.00 /0.00 B:21.56 /0.00 @:0 B@:0
2022-01-13 08:24:51,868 - Recv: echo:busy: processing
2022-01-13 08:24:52,635 - Recv:  T:20.00 /0.00 B:21.56 /0.00 @:0 B@:0
2022-01-13 08:24:53,871 - Recv: echo:busy: processing
2022-01-13 08:24:54,638 - Recv:  T:20.00 /0.00 B:21.56 /0.00 @:0 B@:0
2022-01-13 08:24:55,876 - Recv: echo:busy: processing
2022-01-13 08:24:56,642 - Recv:  T:20.00 /0.00 B:21.56 /0.00 @:0 B@:0
2022-01-13 08:24:57,879 - Recv: echo:busy: processing
2022-01-13 08:24:58,645 - Recv:  T:20.00 /0.00 B:21.68 /0.00 @:0 B@:0
2022-01-13 08:24:59,884 - Recv: echo:busy: processing
2022-01-13 08:25:00,648 - Recv:  T:20.00 /0.00 B:21.33 /0.00 @:0 B@:0
2022-01-13 08:25:01,885 - Recv: echo:busy: processing
2022-01-13 08:25:02,652 - Recv:  T:20.00 /0.00 B:21.33 /0.00 @:0 B@:0
2022-01-13 08:25:03,890 - Recv: echo:busy: processing
2022-01-13 08:25:03,892 - Recv: ok
2022-01-13 08:25:03,902 - Send: N7 M113 S2*102
2022-01-13 08:25:03,921 - Recv: ok
2022-01-13 08:25:03,928 - Send: N8 M104 S{material_print_temperature}*77
2022-01-13 08:25:03,933 - Recv: ok
2022-01-13 08:25:03,937 - Send: N9 M190 S{material_bed_temperature}*83
2022-01-13 08:25:03,942 - Recv: ok
2022-01-13 08:25:03,946 - Send: N10 M109 S{material_print_temperature}*121
2022-01-13 08:25:03,951 - Recv: ok
2022-01-13 08:25:03,958 - Send: N11 M300 S1000 P500*39
2022-01-13 08:25:03,971 - Recv: ok
2022-01-13 08:25:03,979 - Send: N12 G28 X0 Y10 Z0*90
2022-01-13 08:25:04,656 - Recv:  T:20.12 /0.00 B:21.60 /0.00 @:0 B@:0
2022-01-13 08:25:05,987 - Recv: echo:busy: processing
2022-01-13 08:25:06,659 - Recv:  T:20.00 /0.00 B:21.76 /0.00 @:0 B@:0
2022-01-13 08:25:07,991 - Recv: echo:busy: processing
2022-01-13 08:25:08,663 - Recv:  T:19.96 /0.00 B:21.60 /0.00 @:0 B@:0
2022-01-13 08:25:09,995 - Recv: echo:busy: processing
2022-01-13 08:25:10,667 - Recv:  T:19.96 /0.00 B:21.52 /0.00 @:0 B@:0
2022-01-13 08:25:10,853 - Recv: X:-5.00 Y:0.00 Z:0.00 E:0.00 Count X:-404 Y:0 Z:0
2022-01-13 08:25:10,856 - Recv: ok
2022-01-13 08:25:10,864 - Send: N13 M420 S1*85
2022-01-13 08:25:10,879 - Recv: Error:Failed to enable Bed Leveling
2022-01-13 08:25:10,888 - Changing monitoring state from "Starting" to "Error"
2022-01-13 08:25:10,891 - Send: M112
2022-01-13 08:25:10,897 - Send: N14 M112*20
2022-01-13 08:25:10,907 - Send: N15 M104 T0 S0*21
2022-01-13 08:25:10,914 - Send: N16 M140 S0*82
2022-01-13 08:25:10,943 - Changing monitoring state from "Error" to "Offline after error"
2022-01-13 08:25:10,947 - Connection closed, closing down monitor