2020-01-15 12:22:08,694 - serial.log is currently not enabled, you can enable it via Settings > Serial Connection > Log communication to serial.log
2020-01-17 11:44:34,672 - Enabling serial logging
2020-01-17 11:44:51,729 - Connecting to: /dev/ttyUSB0
2020-01-17 11:44:51,748 - Changing monitoring state from "Offline" to "Opening serial port"
2020-01-17 11:44:51,755 - Connected to: Serial<id=0x6ab0bd70, open=True>(port='/dev/ttyUSB0', baudrate=250000, bytesize=8, parity='N', stopbits=1, timeout=10.0, xonxoff=False, rtscts=False, dsrdtr=False), starting monitor
2020-01-17 11:44:51,757 - Changing monitoring state from "Opening serial port" to "Connecting"
2020-01-17 11:44:51,773 - Send: N0 M110 N0*125
2020-01-17 11:44:51,776 - Send: N0 M110 N0*125
2020-01-17 11:44:52,661 - Recv: start
2020-01-17 11:44:52,665 - Send: N0 M110 N0*125
2020-01-17 11:44:52,666 - Recv: echo:Marlin 1.1.4
2020-01-17 11:44:52,668 - Recv: 
2020-01-17 11:44:52,669 - Recv: echo: Last Updated: 2017-07-04 12:00 | Author: (none, default config)
2020-01-17 11:44:52,671 - Recv: Compiled: Jan  8 2020
2020-01-17 11:44:52,672 - Recv: echo: Free Memory: 3653  PlannerBufferBytes: 1232
2020-01-17 11:44:52,675 - Recv: echo:V39 stored settings retrieved (493 bytes; crc 10628)
2020-01-17 11:44:52,677 - Recv: echo:  G21    ; Units in mm
2020-01-17 11:44:52,679 - Recv: echo:  M149 C ; Units in Celsius
2020-01-17 11:44:52,680 - Recv: 
2020-01-17 11:44:52,681 - Recv: echo:Filament settings: Disabled
2020-01-17 11:44:52,683 - Recv: echo:  M200 D3.00
2020-01-17 11:44:52,684 - Recv: echo:  M200 T1 D3.00
2020-01-17 11:44:52,685 - Recv: echo:  M200 D0
2020-01-17 11:44:52,687 - Recv: echo:Steps per unit:
2020-01-17 11:44:52,688 - Recv: echo:  M92 X100.00 Y100.00 Z400.00 E150.00
2020-01-17 11:44:52,689 - Recv: echo:Maximum feedrates (units/s):
2020-01-17 11:44:52,692 - Recv: echo:  M203 X300.00 Y300.00 Z5.00 E25.00
2020-01-17 11:44:52,694 - Recv: echo:Maximum Acceleration (units/s2):
2020-01-17 11:44:52,695 - Recv: echo:  M201 X3000 Y3000 Z100 E10000
2020-01-17 11:44:52,697 - Recv: echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
2020-01-17 11:44:52,699 - Recv: echo:  M204 P3000.00 R3000.00 T3000.00
2020-01-17 11:44:52,702 - Recv: echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_ms> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk>
2020-01-17 11:44:52,704 - Recv: echo:  M205 S0.00 T0.00 B20000 X20.00 Y20.00 Z0.40 E5.00
2020-01-17 11:44:52,706 - Recv: echo:Home offset:
2020-01-17 11:44:52,707 - Recv: echo:  M206 X0.00 Y0.00 Z0.00
2020-01-17 11:44:52,708 - Recv: echo:Auto Bed Leveling:
2020-01-17 11:44:52,710 - Recv: echo:  M420 S0 Z0.00
2020-01-17 11:44:52,711 - Recv: echo:Material heatup parameters:
2020-01-17 11:44:52,712 - Recv: echo:  M145 S0 H240 B60 F0
2020-01-17 11:44:52,714 - Recv:   M145 S1 H240 B60 F0
2020-01-17 11:44:52,715 - Recv: echo:PID settings:
2020-01-17 11:44:52,716 - Recv: echo:  M301 P22.20 I1.08 D114.00
2020-01-17 11:44:52,717 - Recv: echo:  M304 P10.00 I0.02 D305.40
2020-01-17 11:44:52,719 - Recv: echo:Z-Probe Offset (mm):
2020-01-17 11:44:52,720 - Recv: echo:  M851 Z-1.42
2020-01-17 11:44:58,548 - Recv: echo:SD init fail
2020-01-17 11:44:58,559 - Recv: ok
2020-01-17 11:44:58,566 - Changing monitoring state from "Connecting" to "Operational"
2020-01-17 11:44:58,586 - Send: N0 M110 N0*125
2020-01-17 11:44:58,623 - Recv: ok
2020-01-17 11:44:58,627 - Send: N1 M115*39
2020-01-17 11:44:58,645 - Recv: FIRMWARE_NAME:Marlin 1.1.4 (Github) SOURCE_CODE_URL:https://github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:3D Printer EXTRUDER_COUNT:2 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
2020-01-17 11:44:58,671 - Recv: Cap:EEPROM:1
2020-01-17 11:44:58,694 - Recv: Cap:AUTOREPORT_TEMP:1
2020-01-17 11:44:58,702 - Recv: Cap:PROGRESS:0
2020-01-17 11:44:58,706 - Recv: Cap:PRINT_JOB:1
2020-01-17 11:44:58,737 - Recv: Cap:AUTOLEVEL:1
2020-01-17 11:44:58,742 - Recv: Cap:Z_PROBE:1
2020-01-17 11:44:58,745 - Recv: Cap:LEVELING_DATA:1
2020-01-17 11:44:58,752 - Recv: Cap:SOFTWARE_POWER:0
2020-01-17 11:44:58,757 - Recv: Cap:TOGGLE_LIGHTS:0
2020-01-17 11:44:58,761 - Recv: Cap:CASE_LIGHT_BRIGHTNESS:0
2020-01-17 11:44:58,769 - Recv: Cap:EMERGENCY_PARSER:0
2020-01-17 11:44:58,774 - Recv: ok
2020-01-17 11:44:58,775 - Send: M21
2020-01-17 11:45:00,788 - Recv: echo:SD init fail
2020-01-17 11:45:00,792 - Recv: ok
2020-01-17 11:45:00,799 - Send: M420V1
2020-01-17 11:45:00,804 - Recv: Bilinear Leveling Grid:
2020-01-17 11:45:00,807 - Recv:       0      1      2      3
2020-01-17 11:45:00,813 - Recv:  0 -0.013 +0.070 -0.015 -0.018
2020-01-17 11:45:00,817 - Recv:  1 -0.108 +0.077 -0.088 -0.155
2020-01-17 11:45:00,819 - Recv:  2 -0.090 +0.002 -0.018 -0.160
2020-01-17 11:45:00,823 - Recv:  3 -0.005 +0.045 -0.058 -0.123
2020-01-17 11:45:00,826 - Recv: 
2020-01-17 11:45:00,827 - Recv: echo:Bed Leveling Off
2020-01-17 11:45:00,830 - Recv: echo:Fade Height Off
2020-01-17 11:45:00,833 - Recv: ok
2020-01-17 11:45:00,838 - Send: M851
2020-01-17 11:45:00,843 - Recv: echo:Z Offset : -1.42
2020-01-17 11:45:00,845 - Recv: ok
2020-01-17 11:45:00,848 - Send: M155 S2
2020-01-17 11:45:00,854 - Recv: ok
2020-01-17 11:45:02,857 - Recv:  T:211.41 /0.00 B:77.54 /0.00 @:0 B@:0
2020-01-17 11:45:02,883 - Connection closed, closing down monitor
2020-01-17 11:45:02,895 - Changing monitoring state from "Operational" to "Offline"