Error on prusa mk3s

What is the problem?

so i have a problem after updating the octoprint to the latest version and it is quite annoying because it locks the printer every time

What did you already try to solve it?

reset 3d printer and changed the heatbreak and termal sensor

Have you tried running in safe mode?

yes

Did running in safe mode solve the problem?

nope

Systeminfo Bundle

You can download this in OctoPrint's System Information dialog ... no bundle, no support!)

octoprint-systeminfo-20220816132505.zip (81.8 KB)
octoprint-systeminfo-20220816132505.zip (81.8 KB)

WRITE HERE

Additional information about your setup

Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Recv: ok
Send: N73695 M70 P40 (PRUSA 192.168.15.15_)94
Recv: ok
Send: N73696 M400
42
Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
Recv: Resend: 73695
Printer keeps requesting line 73695 again and again, communication stuck
Changing monitoring state from "Finishing" to "Error"
Send: M112
Send: N73697 M11245
Send: N73698 M104 T0 S0
34
Send: N73699 M140 S0*103
Changing monitoring state from "Error" to "Offline after error"
Connection closed, closing down monitor
Closing down send loop
**

WRITE HERE

I assume it's the M70 command

| Send: N73695 M70 P40 (PRUSA 192.168.15.15_)*94
| Recv: ok
| Send: N73696 M400*42
| Recv: Error:Line Number is not Last Line Number+1, Last Line: 73694
| Recv: Resend: 73695

Prusa firmware gives an OK, but can't handle it.

Actually, this is a MakerBot only command:

https://reprap.org/wiki/G-code#M70:_Display_message

Also there seem to be some EMI issues with the USB connection to the printer.
There are some resend requests.

1 Like

This topic was automatically closed 90 days after the last reply. New replies are no longer allowed.