Hi,
I need help with my Ender 5Pro with new firmware from Creality and Octoprint with the latest FW.
I have just updated my E5Pro FW with "firmware Ender-5 ProMarlin2.0.6HW4.2.2ALTE137.bin".
It looks like the firmware is for my printer version: I have 4.2.2 board, BLTouch and TMC2209.
After clicking "connect" in OctoPrint the printer locks (nothing happens when I turn the knob) and I get the following in the Octo's terminal:
Recv: echo:Cannot open subdir S¿7µ\x9dø\x18\x10.\x05F
Recv: echo:Cannot open subdir 0½
Recv: echo:Cannot open subdir 8½\x07µË\x17
Recv: echo:Cannot open subdir 8F1Fı#ð.\x1dû\x18
Recv: echo:Cannot open subdir S¿7µ\x9dø\x18\x10.\x05F
Recv: echo:Cannot open subdir 0½
Recv: echo:Cannot open subdir 8½\x07µË\x17
Recv: echo:Cannot open subdir 8F1Fı#ð.\x1dû\x18
Recv: echo:Cannot open subdir S¿7µ\x9dø\x18\x10.\x05F
And so on...
And it scrolls all the time.
When I disconnect the printer with the OctoPrint button, the printer remains locked and the OP cannot connect again with the message:
Could not autodetect your printer
No working connection parameters could be found. Are you sure your printer is physically connected and supported? Refer to the FAQ for help in debugging this.
What did you already try to solve it?
- I ran the OP in safemode - did not help.
- I have tried with different USB cables (though everything was ok earlier)
- without connecting to OP the printer works ok with new FW
Have you tried running in safe mode?
YES
Did running in safe mode solve the problem?
NO
Systeminfo Bundle
browser.user_agent : Mozilla/5.0 (Windows NT 10.0; Win64; x64; rv:100.0) Gecko/20100101 Firefox/100.0
connectivity.connection_check : 1.1.1.1:53
connectivity.connection_ok : true
connectivity.enabled : true
connectivity.online : true
connectivity.resolution_check : octoprint.org
connectivity.resolution_ok : true
env.hardware.cores : 4
env.hardware.freq : 1400
env.hardware.ram : 914006016
env.os.bits : 32
env.os.id : linux
env.os.platform : linux
env.plugins.pi_support.model : Raspberry Pi 3 Model B Plus Rev 1.3
env.plugins.pi_support.octopi_version : 0.18.0
env.plugins.pi_support.octopiuptodate_build : 0.18.0-1.8.0rc1-20220314112504
env.plugins.pi_support.throttle_state : 0x0
env.python.pip : 20.3.3
env.python.version : 3.7.3
env.python.virtualenv : true
octoprint.last_safe_mode.date : 2022-05-30T17:13:59Z
octoprint.last_safe_mode.reason : settings
octoprint.safe_mode : true
octoprint.version : 1.8.1
systeminfo.generated : 2022-05-30T17:26:36Z
systeminfo.generator : systemapi
Additional information about your setup
OctoPrint version, Version 1.8.1
OctoPi version, Version 0.18.0, running on Raspberry Pi 3 Model B Plus Rev 1.3
printer, Ender 5 Pro
firmware, firmware Ender-5 ProMarlin2.0.6HW4.2.2ALTE137
browser, Firefox 100.0.2 (64 bity)
operating system, Windows 10 x64