What is the problem?
I'm unable to set nozzle temperature, I bed temperature is up not able to set nozzle temperature. it was working fine and ew cancel it is not working
What did you already try to solve it?
I tried setting bed temperature manually from octoprint, it didn't work. tried restarting, didn't work
Have you tried running in safe mode and if so did it solve the issue?
yes, it is still there
octoprint.log
, serial.log
or output on terminal tab at a minimum , browser error console if UI issue ... no logs, no support! Not log excerpts, complete logs.)
WRITE HERE
Additional information about your setup
Version 1.4.2, OctoPi version,cr10s, meirlin 2 , crome, WIN 10
I tried restarting the whole pi systemoctoprint (3).log (2.3 MB) , then got the error "Your printer's firmware reported an error. Due to that OctoPrint will disconnect. Reported error: Heating failed, the system stopped! Heater_ID: bed - Printer halted. kill() called!
"
Please do not open a new thread for the same issue:
octoprint (1).log (187.5 KB)
I use cr10s, the octopi were working fine a few days ago, I haven't used it for some time. I tried running octopi and octoprint and got the error message. I have no SD inn my printer, no test mode and set Temperature interval (Auto report) to 0 (i.e. turn off Auto report. the octoprint is updating bed heating but not heating and no nozzle heating
As I told you there: you have a hardware problem:
2020-11-12 17:55:33,495 - octoprint.util.comm - WARNING - Received an error from the printer's firmware: Heating failed, system stopped! Heater_ID: bed - Printer halted. kill() called!
| Last lines in terminal:
| Recv: T:28.64 /0.00 B:28.22 /40.00 @:0 B@:127 W:?
| Recv: T:28.61 /0.00 B:28.28 /40.00 @:0 B@:127
| Recv: T:28.55 /0.00 B:28.28 /40.00 @:0 B@:127 W:?
| Recv: T:28.64 /0.00 B:28.22 /40.00 @:0 B@:127 W:?
| Recv: T:28.49 /0.00 B:28.12 /40.00 @:0 B@:127
| Recv: T:28.72 /0.00 B:28.37 /40.00 @:0 B@:127 W:?
| Recv: T:28.64 /0.00 B:28.25 /40.00 @:0 B@:127 W:?
| Recv: T:28.52 /0.00 B:28.25 /40.00 @:0 B@:127
| Recv: T:28.44 /0.00 B:28.25 /40.00 @:0 B@:127 W:?
| Recv: T:28.75 /0.00 B:28.31 /40.00 @:0 B@:127 W:?
| Recv: T:28.52 /0.00 B:28.16 /40.00 @:0 B@:127
| Recv: T:28.66 /0.00 B:28.31 /40.00 @:0 B@:127 W:?
| Recv: T:28.72 /0.00 B:28.25 /40.00 @:0 B@:127 W:?
| Recv: T:28.58 /0.00 B:28.25 /40.00 @:0 B@:127
| Recv: T:28.47 /0.00 B:28.16 /40.00 @:0 B@:127 W:?
| Recv: T:28.52 /0.00 B:28.31 /40.00 @:0 B@:127 W:?
| Recv: T:28.61 /0.00 B:28.19 /40.00 @:0 B@:127
| Recv: T:28.49 /0.00 B:28.19 /40.00 @:0 B@:127 W:?
| Recv: Error:Heating failed, system stopped! Heater_ID: bed
| Recv: Error:Printer halted. kill() called!
You have a thermal runaway issue. You set the bed to 40°C, but it does not heat up.
Check the cables of the bed.
Check if the bed thermistor is detached from the bed.
Check if the printer is powered on. -> The display may be lit, but than can be by an issue of the board the the processor and display is powered by the Pi.
1 Like