|
Available hard disk space
|
|
12
|
2658
|
December 10, 2024
|
|
RPI 4 UnderVolt issue
|
|
8
|
972
|
November 28, 2024
|
|
Resolved: Octoprint swallowing extruder switch commands
|
|
4
|
644
|
November 28, 2024
|
|
Anycubic Kobra 3 support
|
|
4
|
2056
|
November 8, 2024
|
|
OctoPI inside of OrcaSlicer
|
|
3
|
3597
|
November 4, 2024
|
|
Print enable/disable from pi pin
|
|
0
|
403
|
November 3, 2024
|
|
Cant decide need help
|
|
5
|
996
|
November 2, 2024
|
|
Got RTSP on octopi working
|
|
2
|
5323
|
September 27, 2023
|
|
Are achievements stored in my account or in the installation (RPi)
|
|
4
|
1176
|
October 22, 2024
|
|
Possible solution to Communication timeout when printing errors
|
|
5
|
3752
|
October 20, 2024
|
|
Octopi-wpa-supplicant.txt does not affect wifi
|
|
12
|
7972
|
October 17, 2024
|
|
Can I get rid of annoying reauthenticate popups?
|
|
14
|
1580
|
October 3, 2024
|
|
Tried Klipper. It is not for me
|
|
9
|
4192
|
September 28, 2024
|
|
Extra bit apparently added by OctoPrint
|
|
10
|
559
|
September 27, 2024
|
|
Pausing and Resuming via M601
|
|
11
|
7659
|
September 26, 2024
|
|
Octoprint Starts on layer zero
|
|
1
|
505
|
September 15, 2024
|
|
Wont start after Python update?
|
|
11
|
892
|
September 15, 2024
|
|
Minimum hardware requirement?
|
|
18
|
61370
|
September 14, 2024
|
|
Anyone using Bambu Lab A1
|
|
1
|
2588
|
September 2, 2024
|
|
Web Socket issue exposing OctoPrint using cloudflared (formerly argo)
|
|
6
|
3761
|
August 31, 2024
|
|
Hey everyone.I am Shubham Saxena
|
|
1
|
703
|
August 27, 2024
|
|
Colour of grid in GCode Viewer
|
|
1
|
756
|
August 26, 2024
|
|
Nozzle Temperature Question
|
|
2
|
900
|
August 23, 2024
|
|
Zero to Hero; My Octo4A setup
|
|
4
|
1658
|
August 9, 2024
|
|
Button Clicking Sounds?
|
|
8
|
1016
|
August 8, 2024
|
|
Raspberry Pi & Ender 3 v3 SE, thoughts…
|
|
9
|
18970
|
July 28, 2024
|
|
Ender 3 replacement advice
|
|
2
|
603
|
July 23, 2024
|
|
Octoprint with ESP32 with camera
|
|
31
|
36782
|
July 19, 2024
|
|
KlipperScreen configuration on OctoKlipperPi
|
|
6
|
5453
|
July 19, 2024
|
|
Hey Guys I am trying to print this part but part is not sticking to bed. I tried increasing bed temperature to 55C still no help. any solution for this issue?
|
|
7
|
1041
|
October 16, 2024
|