|
CR-10s and Bltouch
|
|
5
|
846
|
November 16, 2020
|
|
Frustation with Octoprint
|
|
11
|
1398
|
November 15, 2020
|
|
Preheat plugins
|
|
5
|
2705
|
November 15, 2020
|
|
[PSU-Control] want to improve wiki with tasmota shell command
|
|
1
|
1524
|
November 14, 2020
|
|
Print jobs failures
|
|
1
|
967
|
November 14, 2020
|
|
Suppressing temperature messages
|
|
3
|
1169
|
November 14, 2020
|
|
Predator/Duet 2 wifi with OctoPrint to run a Palette 2 Pro?
|
|
3
|
1471
|
November 14, 2020
|
|
Octoprint unable to connect if printer is off when RPi boots
|
|
11
|
2742
|
November 14, 2020
|
|
Thanks guy's for all the help
|
|
0
|
604
|
November 14, 2020
|
|
Raspberry Shutdown after Print finished?
|
|
10
|
6061
|
November 14, 2020
|
|
Unable to set nozzle temperature
|
|
1
|
3837
|
November 13, 2020
|
|
Octoprint Timeout
|
|
5
|
1166
|
November 13, 2020
|
|
Octoprint 1.5.0rc1 only runs in safe mode
|
|
22
|
3917
|
November 13, 2020
|
|
Communication Error
|
|
38
|
9571
|
November 13, 2020
|
|
Octoprint Z offset too high and will not go any lower through control
|
|
12
|
5204
|
November 13, 2020
|
|
HTTP Authentication enabled - is gcode upload via the API still possible from PrusaSlicer?
|
|
8
|
1271
|
November 13, 2020
|
|
Octoprint no longer connects if port set to AUTO
|
|
48
|
19892
|
November 13, 2020
|
|
Pi 4 Octoprint states Server Offline
|
|
1
|
844
|
November 13, 2020
|
|
Data-bind do not work in my mixin_tab
|
|
2
|
1143
|
November 13, 2020
|
|
BIGTREETECH PI TFT50 V1.0 TFT-display for Raspberry pi supports multiple instances?
|
|
0
|
1395
|
November 13, 2020
|
|
Setup v3 (replacing Pi W with Pi 4)
|
|
3
|
1958
|
November 12, 2020
|
|
My Creality printer shows a heater failure when connected to OctoPrint
|
|
3
|
5172
|
November 12, 2020
|
|
Getting a Mimo Touch 2 to work with OctoPi
|
|
0
|
569
|
November 12, 2020
|
|
Different UI views from different computers of same RPI
|
|
2
|
657
|
November 11, 2020
|
|
Safely shutting down / power off the printer and Octoprint itself
|
|
11
|
5266
|
November 11, 2020
|
|
Octoprint to monitor my 3d prints
|
|
3
|
774
|
November 11, 2020
|
|
Octoprint and CURA v 4.8.0
|
|
2
|
3242
|
November 11, 2020
|
|
Backpowering problems
|
|
15
|
3049
|
November 11, 2020
|
|
OctoPrint GCode System Commands
|
|
0
|
1100
|
November 11, 2020
|
|
Octoprint server not running after plugin install failure
|
|
13
|
1100
|
November 11, 2020
|