|
Print jobs failures
|
|
1
|
662
|
November 14, 2020
|
|
Suppressing temperature messages
|
|
3
|
928
|
November 14, 2020
|
|
Predator/Duet 2 wifi with OctoPrint to run a Palette 2 Pro?
|
|
3
|
1216
|
November 14, 2020
|
|
Octoprint unable to connect if printer is off when RPi boots
|
|
11
|
2241
|
November 14, 2020
|
|
Thanks guy's for all the help
|
|
0
|
461
|
November 14, 2020
|
|
Raspberry Shutdown after Print finished?
|
|
10
|
5819
|
November 14, 2020
|
|
Unable to set nozzle temperature
|
|
1
|
3284
|
November 13, 2020
|
|
Octoprint Timeout
|
|
5
|
939
|
November 13, 2020
|
|
Octoprint 1.5.0rc1 only runs in safe mode
|
|
22
|
3004
|
November 13, 2020
|
|
Communication Error
|
|
38
|
8432
|
November 13, 2020
|
|
Octoprint Z offset too high and will not go any lower through control
|
|
12
|
4506
|
November 13, 2020
|
|
HTTP Authentication enabled - is gcode upload via the API still possible from PrusaSlicer?
|
|
8
|
1068
|
November 13, 2020
|
|
Octoprint no longer connects if port set to AUTO
|
|
48
|
17879
|
November 13, 2020
|
|
Pi 4 Octoprint states Server Offline
|
|
1
|
693
|
November 13, 2020
|
|
Data-bind do not work in my mixin_tab
|
|
2
|
943
|
November 13, 2020
|
|
BIGTREETECH PI TFT50 V1.0 TFT-display for Raspberry pi supports multiple instances?
|
|
0
|
1221
|
November 13, 2020
|
|
Setup v3 (replacing Pi W with Pi 4)
|
|
3
|
1563
|
November 12, 2020
|
|
My Creality printer shows a heater failure when connected to OctoPrint
|
|
3
|
4410
|
November 12, 2020
|
|
Getting a Mimo Touch 2 to work with OctoPi
|
|
0
|
425
|
November 12, 2020
|
|
Different UI views from different computers of same RPI
|
|
2
|
509
|
November 11, 2020
|
|
Safely shutting down / power off the printer and Octoprint itself
|
|
11
|
4530
|
November 11, 2020
|
|
Octoprint to monitor my 3d prints
|
|
3
|
607
|
November 11, 2020
|
|
Octoprint and CURA v 4.8.0
|
|
2
|
2864
|
November 11, 2020
|
|
Backpowering problems
|
|
15
|
2358
|
November 11, 2020
|
|
OctoPrint GCode System Commands
|
|
0
|
938
|
November 11, 2020
|
|
Octoprint server not running after plugin install failure
|
|
13
|
898
|
November 11, 2020
|
|
Commands are ignored until i press "fake acknowledgement"
|
|
3
|
1345
|
November 11, 2020
|
|
Octopi does not see printer (but PC does)
|
|
8
|
2522
|
November 10, 2020
|
|
Enclosure plugin - temperature sensor problems
|
|
3
|
2247
|
November 10, 2020
|
|
Firmware Updater not working
|
|
12
|
4499
|
November 10, 2020
|