|
MultiCam not working with 1.11.x anymore (str vs. object)
|
|
3
|
597
|
May 17, 2025
|
|
Plugin that allows Octoprint to use local printer display
|
|
6
|
1579
|
May 2, 2025
|
|
Plugins That Put Camera in Sidebar
|
|
6
|
637
|
April 26, 2025
|
|
Is there a plugin that can delay print start after preheat?
|
|
2
|
700
|
April 14, 2025
|
|
Automatic Slicer
|
|
7
|
10677
|
April 10, 2025
|
|
Astroprint Plugin not Working
|
|
11
|
1219
|
April 10, 2025
|
|
Astroprint Plugin Install Issue
|
|
12
|
3898
|
April 10, 2025
|
|
Automatic switch-off of the printer if the temperature is too high
|
|
3
|
544
|
April 5, 2025
|
|
Bambu A1 - Auth Token
|
|
8
|
2316
|
April 2, 2025
|
|
PSU Control don´t work for no reason
|
|
27
|
3807
|
April 1, 2025
|
|
Lulzbot mini 1 settings for firmware updater
|
|
1
|
598
|
March 23, 2025
|
|
All 3rd-party plugins GONE... Can't re-install
|
|
19
|
2868
|
March 20, 2025
|
|
Octodash on seperate rPi?
|
|
10
|
2238
|
March 12, 2025
|
|
Bed Visualizer says everything is ~ 3mm below offset
|
|
6
|
525
|
March 10, 2025
|
|
TimeLapse + (Plus)
|
|
0
|
560
|
March 7, 2025
|
|
Octolapse - Not extruding after 1st layer
|
|
7
|
2855
|
March 5, 2025
|
|
Printer setup and tuning Plugin?
|
|
2
|
1268
|
February 25, 2025
|
|
Use of GCODE system commands
|
|
2
|
1093
|
February 23, 2025
|
|
Octolapse Error File line number 2 was expected, but 2 was received!
|
|
15
|
1910
|
February 21, 2025
|
|
Smart Preheat (Not so smart)
|
|
7
|
3206
|
February 17, 2025
|
|
TeraBox Plug-In.?
|
|
4
|
2462
|
February 12, 2025
|
|
Enclosure plugin no temp showing
|
|
5
|
944
|
February 6, 2025
|
|
Cura OctoPrint Connection plugin
|
|
414
|
157419
|
February 2, 2025
|
|
Camera Settings plugin not saving settings
|
|
2
|
784
|
January 30, 2025
|
|
Octolapse Printer not primed error
|
|
1
|
2152
|
January 30, 2025
|
|
Using the Tasmota plugin and Print Scheduler together
|
|
4
|
1740
|
January 19, 2025
|
|
Is it possible to Schedule a print with power on
|
|
10
|
2692
|
January 19, 2025
|
|
ERROR: Failed building wheel for Octolapse
|
|
14
|
3610
|
January 18, 2025
|
|
Snapshots not matching with preview
|
|
1
|
493
|
January 17, 2025
|
|
The Z Probe Offset Plugin is located behind the FlowratePlugin
|
|
3
|
829
|
January 16, 2025
|