|
Error installing plugin - Exclude Region
|
|
1
|
1276
|
August 26, 2020
|
|
Cant connect to Octoprint via OpenVPN
|
|
4
|
2552
|
July 3, 2020
|
|
Ender 3 pro usb problem
|
|
3
|
2851
|
May 31, 2021
|
|
Webcam fails after a while, discovered port conflict upon webcamd restart
|
|
6
|
2155
|
January 17, 2020
|
|
Help needed please...my prints are not centering on my lulxbot TAZ 6
|
|
5
|
2328
|
March 25, 2018
|
|
Hot-end temperature wildly fluctuates
|
|
7
|
2015
|
July 7, 2021
|
|
Octoprint not accessible via hostname after print starts
|
|
7
|
2015
|
May 27, 2019
|
|
How to set flow rate?
|
|
2
|
3290
|
March 31, 2018
|
|
No /etc/default/octoprint
|
|
7
|
2013
|
December 6, 2020
|
|
Multiple Internal IP Addresses for a Single External IP Address
|
|
5
|
2323
|
March 23, 2018
|
|
Need help with configuing time on pi
|
|
7
|
2011
|
February 7, 2021
|
|
Small question on the usb Pi4 CR-6
|
|
5
|
2322
|
January 29, 2021
|
|
Guest Access Removed?
|
|
3
|
2840
|
January 29, 2019
|
|
New release candidate: 1.3.9rc3
|
|
0
|
1010
|
July 16, 2018
|
|
Octopi Nightly Builds
|
|
3
|
2834
|
November 25, 2018
|
|
How to disable terminal messages by default?
|
|
6
|
677
|
July 14, 2022
|
|
New release candidate: 1.3.9rc4
|
|
0
|
1007
|
July 20, 2018
|
|
SD resolution for 1080p camera
|
|
4
|
2532
|
October 18, 2023
|
|
Can't get Octopi to boot/startup
|
|
4
|
2530
|
October 16, 2019
|
|
No more working Filament Sensor Plugin for Octoprint?
|
|
6
|
2138
|
November 5, 2020
|
|
I use octoprint on a PC, but cannot connect form the other PC
|
|
3
|
2828
|
April 6, 2020
|
|
Octoprint believed the print was already finished and started cooling but the printer wasn't actually done!
|
|
7
|
1999
|
January 27, 2020
|
|
3D Printer USB-Serial Problems
|
|
2
|
3262
|
May 7, 2022
|
|
Pause & Park Scripts, Stringing/Layer Line
|
|
3
|
2824
|
September 9, 2020
|
|
ESP32-cam stream not loaded (SOLVED)
|
|
2
|
3260
|
November 28, 2021
|
|
[Advertisement] Filament change time (M600)
|
|
0
|
1004
|
February 5, 2020
|
|
Raspi Cam isn't working
|
|
7
|
1996
|
February 22, 2022
|
|
Need help getting a GPIO LOW after shutdown
|
|
7
|
1995
|
August 28, 2022
|
|
PSU control no longer switching relay
|
|
5
|
2304
|
April 22, 2021
|
|
Trouble Logging into OctoPrint on Orange Pi Zero
|
|
4
|
2521
|
October 7, 2023
|
|
OctoPrint Update from 1.10.0 to 1.10.1 or 1.10.2 Fails
|
|
7
|
1993
|
September 25, 2024
|
|
Spoolmanager Plugin -> Failure during installation
|
|
7
|
1992
|
November 6, 2023
|
|
No Longer 'Remember Me' auto login
|
|
7
|
1990
|
January 9, 2020
|
|
Problem with Octoprint remote access and dynamic IP
|
|
7
|
1990
|
June 16, 2018
|
|
Logging in to OctoPi when in an iFrame (even with auto-login)
|
|
8
|
1876
|
September 23, 2024
|
|
Web Cam on new install with big lag
|
|
6
|
2127
|
April 13, 2021
|
|
What webcam software?
|
|
2
|
3248
|
April 29, 2020
|
|
PiCam stream loading forever
|
|
2
|
1826
|
August 28, 2020
|
|
SOLVED: OctoPrint causes CR10v3 to freak out after BLTouch firmware install
|
|
7
|
1987
|
May 9, 2022
|
|
OctoPrint On Air #15
|
|
5
|
1290
|
April 11, 2018
|
|
What is the benefit of MeatPack Plugin
|
|
6
|
2122
|
July 12, 2021
|
|
Octoprint on macOS; 'Callable' has no attribute '_abc_registry'
|
|
5
|
2290
|
January 3, 2020
|
|
The remote device or resource won't accept the connection
|
|
6
|
2120
|
March 6, 2020
|
|
Temp sensor location
|
|
6
|
2119
|
September 29, 2021
|
|
Octoprint/Octoscreen Touch not working
|
|
3
|
1576
|
September 19, 2023
|
|
Octoprint and Sony Alpha 5100 DSLR - finally working
|
|
0
|
996
|
November 19, 2023
|
|
Installing OctoPrint onto 2019-09-26-raspbian-buster-full
|
|
3
|
2800
|
August 1, 2021
|
|
Boot message: Failed to start the OctoPi WebCam Daemon
|
|
3
|
2800
|
December 31, 2020
|
|
Layer shift when Pie is connected to printer
|
|
4
|
2503
|
November 23, 2020
|
|
Sending commands to printer from plugin
|
|
4
|
2502
|
September 30, 2019
|