|
Observe printer.is_ready
|
|
3
|
833
|
September 9, 2021
|
|
Octoprint server appears broken?
|
|
1
|
3721
|
March 28, 2018
|
|
Enclosure -BME280 no readout in plugin, but otherwise ok
|
|
3
|
2633
|
May 11, 2020
|
|
Password reset commands not working
|
|
2
|
3036
|
December 2, 2019
|
|
Upping Video Resolution?
|
|
7
|
1859
|
April 14, 2022
|
|
cannot seem to disconnect power without losing all data on SD card
|
|
7
|
1854
|
July 11, 2018
|
|
How to send commands/control printer through personal web page
|
|
5
|
2141
|
August 13, 2021
|
|
Setting OctoPrint up first time, country issue please
|
|
3
|
2616
|
March 2, 2020
|
|
Monoprice Mini Delta V2
|
|
3
|
2616
|
June 26, 2022
|
|
[Octopalse] Printer Not Primed - Priming was not detected
|
|
1
|
3698
|
January 14, 2022
|
|
OctoPrint On Air #19
|
|
3
|
1471
|
October 18, 2018
|
|
Can't access octoprint via browser, current username/pw no longer works
|
|
5
|
2135
|
February 17, 2020
|
|
Octoprint cant connect to printer as firmware is corrupted
|
|
6
|
1975
|
December 19, 2021
|
|
Bypassing the Login set on RPi start-up
|
|
2
|
3015
|
December 1, 2018
|
|
Target Temp changes without instruction to do so
|
|
5
|
2131
|
December 5, 2021
|
|
Octoprint, Wifi Socket and power off
|
|
1
|
3690
|
March 2, 2020
|
|
Newer CuraEngine some day?
|
|
5
|
2130
|
October 15, 2018
|
|
Ender 3 pro doesn't connect
|
|
7
|
1844
|
January 30, 2022
|
|
MINTEMP Triggered. HEATER_ID: 0
|
|
6
|
1971
|
November 2, 2020
|
|
New release: 1.8.1
|
|
0
|
926
|
May 24, 2022
|
|
Octoprint doesn't load at octoprint.local
|
|
6
|
1968
|
September 3, 2023
|
|
MPmini v.1, New SD card.(bigger) now octoprint isn't Connecting to specific port, need to disable "AUTO"
|
|
7
|
1839
|
July 15, 2020
|
|
Can connect with octoremote, but can't with local octoprint
|
|
4
|
2328
|
March 7, 2022
|
|
Failed to restart octoprint srvc: Unit octoprint.service not found
|
|
7
|
1841
|
May 1, 2024
|
|
Error updating fresh install from 1.3.10 to 1.3.12
|
|
2
|
3003
|
November 6, 2019
|
|
Can’t seem to login
|
|
3
|
2596
|
November 9, 2020
|
|
Timeout while printing, and looking to eliminate blobs
|
|
7
|
1837
|
January 17, 2021
|
|
Octopi login problem
|
|
3
|
2595
|
February 3, 2021
|
|
Send G-code file to Octoprint from a C program
|
|
6
|
1960
|
November 7, 2020
|
|
Octopi wifi will not work
|
|
4
|
2319
|
July 15, 2022
|
|
Is it possible to image sd card without admin rights
|
|
4
|
2317
|
November 1, 2023
|
|
Jerky movements, printing too slow
|
|
1
|
2060
|
August 10, 2019
|
|
General Question: Delay after serial print (to host)
|
|
6
|
1958
|
March 17, 2018
|
|
Change X Y Offset
|
|
1
|
3663
|
March 20, 2020
|
|
Printer connection problem
|
|
3
|
2591
|
December 5, 2019
|
|
Can't reorder tabs in config.yaml
|
|
5
|
2114
|
May 31, 2020
|
|
Creality Connection Issues
|
|
6
|
1956
|
May 9, 2023
|
|
Chrome freeze after few clicks
|
|
8
|
1722
|
August 4, 2020
|
|
Temperature Jitter on Print
|
|
7
|
1826
|
January 23, 2020
|
|
Plugin stops without any output when using bme280 library
|
|
7
|
1828
|
January 4, 2020
|
|
Informational state types
|
|
7
|
1827
|
May 20, 2018
|
|
OctoDash has No Webcam
|
|
6
|
1952
|
February 12, 2023
|
|
Pip version warning after successful plugin installation
|
|
3
|
2582
|
January 4, 2019
|
|
Setting up a second OctoPrint on same WiFi
|
|
4
|
2309
|
November 22, 2019
|
|
Octoprint and motion on a RPI 3b+
|
|
4
|
2309
|
October 20, 2020
|
|
Octolapse crashes long prints
|
|
7
|
1825
|
December 10, 2018
|
|
Where to place xinput command for startup
|
|
5
|
2106
|
December 26, 2019
|
|
Temp controlled LEDs
|
|
4
|
2308
|
March 7, 2019
|
|
I've been hit by ransomware
|
|
8
|
1719
|
September 2, 2020
|
|
Full Screen Terminal Output
|
|
4
|
2306
|
March 15, 2020
|